How to use the latest version of digital bridge and the principle of digital bridge
Digital bridges are instruments that can measure inductance, capacitance, resistance, and impedance. This is a traditional habit. The earliest impedance measurement uses the true bridge method. With the development of modern analog and digital technologies, it has already been eliminated. This measurement method, but the name of the LCR bridge has been used ever since. If it is a LCR bridge using a microprocessor, it is called an LCR digital bridge. The general users also call these: LCR tester, LCR bridge, LCR meter, LCR Meter and so on.
With the development of modern analog and digital technologies, this measurement method has been eliminated, but the name of the LCR bridge has been used ever since. If it is a LCR bridge using a microprocessor, it is called an LCR digital bridge. The general users also call these: LCR tester, LCR bridge, LCR meter, LCR Meter and so on.
Digital bridge principle
history
Digital bridge (volume name: electrician)
Digital bridge
A bridge that measures impedance parameters using digital techniques. Digital technology is the conversion of traditional analog quantities into digital quantities, followed by digital operations, transmission and processing.
In 1972, the world's first digital capacitive bridge with microprocessors, which combined analog circuits, digital circuits and computer technology, opened up a new path for impedance measuring instruments.
principle
The measurement object of the digital bridge is the parameters of the impedance component, including the AC resistance R, the inductance L and its quality factor Q, the capacitance C and its dissipation factor D. Therefore, the digital bridge is often referred to as a digital LCR meter. The measurement frequency is from the power frequency to about 100 kHz. The basic measurement error is 0.02%, which is generally around 0.1%.
The principle of the digital bridge is shown in the figure. In the figure, the DUT is the device under test, its impedance is represented by Zx, and Rr is a standard resistor. The switch can measure the voltages Ux and Ur of the two, respectively, so there is the following formula:
Balanced bridge test principle
Balanced bridge test principle
Zx = Ux/Ix = Rr * Ux/Ur
This formula is a phasor relationship. If a phase sensitive detector (PSD) is used to measure the in-phase component and the quadrature component of Ux and Ur corresponding to a reference phasor, respectively, and then convert it into a digital quantity by an analog-to-digital conversion (A/D), and then The complex value and the reactance value of the measured impedance Zx can be obtained by a computer performing a complex operation.
It can be seen from the circuit and working principle in the figure that the digital bridge only inherits the traditional name of the bridge. In fact, it has lost the form of the traditional classic AC bridge, but at a higher level back to Ohm's law-based ammeter, voltmeter circuit and principle.
The digital bridge can be used for the verification and transmission of impedance gauges by the metrology test department, as well as the conventional measurement of impedance components in the general sector. Many digital bridges have a standard interface, which can automatically divide the measured components according to the accuracy of the measured value. It can also be directly connected to the automatic test system for automatic inspection of the product on the component production line to realize the production process. QC. In the mid-1980s, there were dozens of digital bridges with a common error of less than 0.1%. Digital bridges are evolving with greater accuracy, more functionality, speed, integration, and intelligence.
Performance characteristics
Wide range of measurement objects
Multiple component and material property measurement capabilities
Instructions
Power up
First connect the power cable with the IEC end to the IEC socket on the left rear of the bridge, the other end to the appropriate power outlet, and move the boat switch on the left rear of the bridge, even if the bridge is energized. When powered up, the display, range, and function indicators light up. The bridge can be automatically placed in the inductor and capacitance measurement files, parallel equivalent and 1KHz frequency state. Under normal circumstances, the internal circuit can be stabilized after a few seconds of power-on, and measurement can be performed.
2. Access method of the tested component
(1) Generally, the components of the radial lead can be directly inserted into the combined test clamp, and the components of the special flexible lead should be connected by the clamp clutch, which is located directly under the test clamp.
(2) When accessing the axial lead components, in order to avoid twisting the leads, an axial adapter can be used. First, insert the two fittings into the two ends of the test clip, and then adjust the spacing to the position suitable for the component measurement, and then The axial lead elements are inserted into the accessory clips at both ends.
(3) Where the axial adapter must be fairly fixed, such as when measuring a large number of similar components, a support plate is required.
Install the support plate: first adjust the axial adapter to the appropriate position, then suspend the support plate over the axial adapter, let each axial adapter pass through the slot on the support plate, and place the support plate Align the fixing screws with the screw holes on the bridge panel and finally tighten the screws. Note: It is not easy to tighten the screws too tightly during installation.
Note: Although the bridge can protect the charging capacitor access test, it is better to measure the charging capacitor after discharging it with a suitable resistor.
3. Note the reading and measurement conditions during use
(1) The 6-bit display of the instrument may not all be valid. In some measurements, the untailed value of the measured data may be large. The jitter values ​​should be discarded and the stable value read.
(2) Generally, the automatic range measurement is used to ensure that the correct range is selected, and the actual working range can be observed by operating to the manual mode. When applied to the batch test of the same batch of the same measuring component, the range lock mode can be selected to work.
(3) string--parallel indication
Although the bridge has the selectivity to display the equivalent values ​​in series or in parallel, in the case of unfavorable Q values, it is impossible to obtain basic accuracy in either of the above two ways. When it is necessary to change a display mode in order to improve the basic accuracy, the bridge indicates the series connection by the subscript s, and the subscript p indicates the parallel connection.
(4) Frequency prompt
Capacitance of 200μF~2000μF, inductance of 200H~2000H, only the basic accuracy can be obtained when the measurement frequency is 100Hz. Similarly, 200pF~2nF capacitors and 200μH~2mH inductors can only obtain basic accuracy at 1KHz measurement frequency. Therefore, for the best test performance, the most suitable test frequency should be selected.
(5) Test level display
High-K ceramic capacitors or high-conductivity magnetic inductors are sensitive to the level of the test signal, and different test levels can produce different measurements. At the same time, the lower the test level, the worse the measurement stability.
4. Recommended measurement conditions reference table
Table measurement condition reference
Component name measurement frequency string - parallel
Capacitance <1μF 1KHz parallel
Capacitance ≥1μF (electroless capacitor) 100Hz parallel
Capacitance ≥1μF (electrolytic capacitor) 100Hz series (SER)
Inductance <1H 1KHz Series (SER)
Inductance ≥1H 100Hz series (SHR)
Resistance <10KΩ 100Hz series (SHR)
Resistance ≥10KΩ 100Hz parallel
When the bridge is capable of providing series and parallel equivalent component values ​​at both 100 Hz and 1 kHz frequencies, it is recommended that certain types and values ​​of components be measured in a certain way. This is done in order to obtain a structural form that is most suitable for the component and that is most suitable for the measurement of the working mode commonly used by the component. For example, a large-capacity electrolytic capacitor, often used as a power filter element, will find that the capacitance at 1KHZ frequency is significantly lower than the capacitance at 100Hz. This phenomenon is due to factors related to the geometry of such components. Therefore, the capacitance value measured by the electrolytic capacitor at a frequency of 100 Hz is most useful. The loss term of the electrolytic capacitor is usually displayed on the series equivalent resistance (ESR), so the series capacitance and series resistance value should be measured.
The company's main stainless steel water collector, tank bottom weld vacuum test box, reading instrument, eight-stage air microbial sampler, relay comprehensive tester, coating thickness gauge, soil grinder, tempered glass surface flatness tester, Sound sensor, portable electric water level gauge, net mouth flow meter, corrosion rate meter, portable scratch tester, freezing point tester, water quality tester, online ammonia tester, coating thickness gauge, coating thickness gauge, soil Crusher, digital thermometer, gas sampling pump, ceramic impact tester, automatic crystallization point tester, drug freezing point tester, reed switch tester, constant temperature water bath, gasoline root transfer, gas sampling pump, tempered glass Tester, water quality tester, PM2.5 tester, inhalable particulate matter detector, high frequency heat sealing machine, strain control triaxial instrument, milk somatic cell detector, helium gas concentration detector, soil moisture conductivity tester, field Strong instrument, collection box, transparency ratio meter, capillary water absorption time measuring instrument, redox potentiometer vibrometer, carbon monoxide carbon dioxide detector, CO2 analyzer, Mud content tester, car starter power supply, automatic potentiometric titrator, portable thermometer, zirconia analyzer, reed switch tester, precision conductivity meter, TOC water quality analyzer, microcomputer plasticity tester, wind direction station, full Automatic spotting instrument, soil redox potentiometer, digital thermometer, portable total phosphorus tester, corrosion rate meter, constant temperature water bath, residual chlorine detector, free expansion rate meter, centrifugal cup, concrete saturated vapor pressure device, pellet Strength Tester, Gauss Meter, Automatic Film Coating Machine, Safety Valve Grinding Tool, Weather Station, Motion Azimuth Instrument, Dark Adaptation Instrument, Odor Collector, Rain Gauge, 4 in 1 Gas Analyzer, Emulsion Concentration Meter, Dissolved Oxygen Instrument, temperature measuring instrument, thin layer paver, temperature recorder, aging instrument, noise detector, constant temperature and humidity chamber, split resistivity tester, initial viscosity and viscosity tester, infrared carbon dioxide analyzer, hydrogen lamp, Kinescing azimuth instrument, constant temperature animal operating table, cooling fan, oil acid value detector, viscosity meter, colony counter, weather station, rain gauge, Kjeldahl Instrument, partial collector, fluorescent whitening agent, flat grinding instrument, fuel cell characteristic comprehensive tester, dissolution instrument, online PH meter, on-site dynamic balance instrument, high vacuum valve, Gabor centrifuge, ultrasonic liquid level transmitter , Abbe refractometer, water quality rapid detector, petroleum product freezing point measuring instrument, petroleum product freezing point measuring instrument, zirconia oxygen analyzer, sludge ratio group measuring device, scanner, handheld four-probe tester, Nitrogen blowing instrument, personal dose alarm device, the company adhering to the "customer first, forge ahead" business philosophy, adhere to the "customer first" principle to provide our clients with quality services. Welcome patrons!
This product has a wide range of uses, not only limited to painting, 3D Drawing Board will bring you more happiness, can inspire children's love for art, make children fall in love with painting, create a colorful atmosphere, good light transmission, no damage to eyes, long service life long.Simple to use, easy to see at a glance, crafted with heart.
Flourescent Drawing Board,magic fluorescent drawing board,3d fluorescent drawing board
Guangdong Jishengke Industrial Co.,Ltd , https://www.jskpads.com