The installation of the chandelier in the living room is very easy for the professional master, but it is very difficult for us to understand the installation of the luminaire, so when we decorate the living room luminaire, we must find a professional master, do not blindly install it yourself. Otherwise it will bring security problems. So what is the installation procedure for the living room chandelier ? We can complete the installation of the lamp according to the operation steps. Let's take a look at it.
First, the preparation tool
No matter which lighting fixture you choose to install, you need to prepare the tools before installation so that there is no problem during installation. Installing the chandelier is first and foremost a tool. Choosing a suitable electric drill is an important part of installing a chandelier. General chandelier installation requires a 6mm hole, so our electric drill should also choose 6mm drill size.
Second, find the hole
After preparing the installation tool, you should find a suitable location for punching, determine the location of the hole, and then perform the punching installation, otherwise the wrong position will be made. Once the tool is installed, put it aside and then start preparing the screws on the top plate. First remove the hanging plate from the ceiling plate, align it with the hole in the ceiling plate, and compare the position and tighten the screws. If the adjustment is not as good as many times, you can try to adjust some screw positions.
Third, drilling
Drilling is very important for the installation of the luminaire, so everyone should pay attention to the drilling, do not blindly drill, otherwise it will cause installation problems. Drilling is a critical step. First mark the position where the expansion screw is needed on the wall, and then start drilling with the pre-installed electric drill. When drilling, be sure to pay attention to the depth of the hole and calculate it according to the length of the expansion screw.
Fourth, the upper screw
There are a lot of screws when installing the luminaire, so we should pay attention when attaching the screws. Do not ignore the fact that some screws are not installed because of the fast, which leads to the aesthetics and safety of the luminaire. Put the expansion screw prepared in advance into the hole, and then use external force to drive it into it. Many people want to fix it by hand, but no, at least use a hammer to drive it in, otherwise it is easy to cause safety problems if it is not strong. Remind, be sure to ensure that the expansion screws are all inside the wall.
Five, fixed hanging board
The scraper must be taken seriously when it is installed. Once the hanging plate is not fixed, the lamp will have certain safety and cannot be used. First, insert the expansion screw completely into the wall, and then start to prepare to fix the hanging plate. First, insert the wood screws through the hole in the hanging plate, and then select the wood screws into the inside along the expansion screws. Be sure to pay attention to the two sides alternately, the installation is firm, there is no offset, otherwise it is not safe.
Sixth, fixed ceiling plate and lamp body
After doing the above steps, even if you have done half of it, the rest is to connect the hanging plate and the ceiling plate with screws. Make sure that the screws are fixed after the connection is completed. After fixing, be sure to check carefully. It is already strong.
The above is about the installation steps of the living room chandelier, I hope to be helpful to everyone! Qi installed network, China's well-known large-scale decoration platform, decoration leading brand. If you want to make a new design, you are advised to apply for the free design service of the net, and help you plan a reasonable space layout and beautiful design through the professional designer's on-site measurement room.
>> Click here for professional designer free room design
Peripheral Devices and Consumables
Based on the low labor cost and reasonable stainless steel cost, Helper help to offer clients internal transport devices with best price. These machines and device include standard material truck, smoking trolley, lifter, conveyer belts, spiral feeding machine, hydraulic lifter etc. The internal transport device is used in filling and forming workshop, tumbling and seasoning workshop, smoking and cooking room etc.
Helper has a professional team to design and produce sausage clips. They have rich experience and understand all the key points for produce good quality clips. From the raw material purchasing to mould designing, from the QC in production to post-treatment, they pay attention to all these details that lead to the good quality of Helper`s clip series. Our clips products include U shape clips, Great wall shape clips, and aluminum wire (for aluminum wire clipper).
U Shape Sausage Clip,Clips On Strip,Bag Packaging Clips,Screw Material Conveyor
Helper Machinery Group Co., Ltd. , https://www.helperfoodmachiney.com